American Seal & Packing American Seal & Packing flag


  Shop Online or Call 714-593-9780
 
 

  Seals and Packing
 


Mechanical Seals
GRAFOIL®Flexible Graphite
Pump Packing
Valve Packing

Injectable Packing
Ameri-lon
Gasket Materials
Spiral Wound Gaskets
High Temperature Seals
O-Rings
Hydraulic Seals
Tadpole Tapes
Silica Tapes
Molded/Machined PTFE
Extruded PTFE
V-Packing
Radial Lip Seals
Expansion Joints
PTFE Lubricants
Pump Seals
Packing Tools

Shop by:
Manufacturers
Special Buys

  Special Services
  Mechanical Seal Repairs
Gasket Cutting
Die Formed Packing
Die Formed Grafoil
Spiral Wound Gaskets
Custom Stitched Tadpole
CNC Machined PTFE
Molded PTFE
Vulcanized O-Rings
 

Injectable Packing

Injectable pump & valve sealant
High Temp Injectable Packing Injectable Packing for high Pressure FDA Injectable Packing Chemically resistant Injectable Packing Abrasive Service Injectable Packing

20 [Order-On-Line]

A composition of flexible graphite particles and elevated-temperature sacrificial lubricants for extreme service injectable packing.

Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications

25 [Order-On-Line]

A chemically resistant product with bearing pellets. Ideal for the toughest applications.

 Available In:

2.2 lb
11 lb
22 lb
Specifications

26[Order-On-Line]

For your applications that cannot be stained our non-toxic fiber blended with FDA-approved lubricants is ideal for clean or food grade applications.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications


27 [Order-On-Line]

A blend of ptfe/graphite fibers producing an abrasive and chemically resistant packing.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications

29[Order-On-Line]

A blend of aramid fibers and non-straining lubricants makes this a durable general service injectable packing.

 Available In:
10-pack stick cartridges
2.2 lb
11 lb
22 lb
Specifications
Injectable Packing injection gun

An Easy and Convenient Product to Use

Injectable sealants are easy to install.  
The
initial
installation of injectable packing materials is done by hand. Tightening the gland nut compresses the packing material and forces it to conform to any irregular spaces caused by wear. An anti-extrusion ring composed of suitably sized braided pump packing material is set at the top and bottom of the stuffing box or packing gland to prevent the injectable packing sealant from being forced out when pressure is applied.

The injection gun

The injection gun utilizes a button-head or flow-through fitting permanently installed on the pump or valve stuffing box.

Since it requires no electricity, the injection gun can be used anywhere to replenish injectable packing easily and conveniently. The all-steel hydraulic gun is completely portable and is very easy to use.

The valve or pump stuffing box fitting allows the injectable packing to be hand-injected into the shaft stuffing box using the injector gun. No downtime is required for the repacking operation since the equipment can continue to run during the repacking operation.

How to use the injection gun

To properly replenish the injectable packing material, the stuffing box fitting must be located. Next, the injection gun is coupled to the fitting.

When the gun is properly coupled to the fitting, the on-off handle on the fitting is turned to the open position and the new injectale sealant is pumped into the fitting until the required amount of packing is injected.

When the operation is complete, the fitting handle is placed in the off position and the gun is disconnected from the stuffing box fitting. Remember to properly disassemble and return your injection gun to its container where it may be stored until needed again.

Note: Button-head fittings with check ball valve do not required ball valve for on-line repacking of injectable packing.

      Call us at: 714-593-9780   Fax: 714-593-9701
 

 






© 2012 American Seal & Packing, Inc.
GRAFOIL® is a registered trademark of GrafTech International Holdings Inc.
Viton® is a registered trademark of DuPont Performance Elastomers.
Kalrez® is a registered trademark of DuPont Performance Elastomers.
GFO® is a registered trademark of W.L. Gore and Associ
ates

American Seal & Packing, Inc., Fountain Valley, CA 92708  •  714-593-9780

Web Site
www.aspseal.com